Ignition Lock Cylinder Removal - Revision history

Smitch at 14:52, 14 May 2010

2010-05-14T14:52:12Z

Smitch at 14:35, 24 April 2010

2010-04-24T14:35:26Z

Smitch at 14:33, 24 April 2010

2010-04-24T14:33:57Z

Smitch at 14:33, 24 April 2010

2010-04-24T14:33:19Z

Smitch: New page: By AMC Eagle Nest Member "Pack Rat". Note: This How-To starts after the steering wheel has been pulled. Please follow this link for a 'How-To' about removing the wheel. [[Re&Re The Wirin...

2010-04-24T14:32:39Z

New page: By AMC Eagle Nest Member "Pack Rat". Note: This How-To starts after the steering wheel has been pulled. Please follow this link for a 'How-To' about removing the wheel. [[Re&Re The Wirin...

New page

By AMC Eagle Nest Member "Pack Rat".

Note: This How-To starts after the steering wheel has been pulled. Please follow this link for a 'How-To' about removing the wheel.
[[Re&Re The Wiring Harness in Your Steering Column]]

Remove the turn signal lever, the push button for the four way flashers then remove the three screws holding the turn signal switch in place. You can then pull the switch up enough that it's not in the way. You'll see or should see if it's still there, a small push in thing with two contacts coming off it, that's the switch for the ignition buzzer. It will pop out. Well not exactely pop, you'll need a small screw driver to help it along. You'll then see either a 5/16th or torx screw head bolt, remove and the switch will pull out of the column.

@@ Line 1: / Line 1: @@
-By AMC Eagle Nest Member "Pack Rat".
+By AMC Eagle Nest member "Pack Rat".
 Note: This How-To starts after the steering wheel has been pulled.
@@ Line 9: / Line 9: @@
 Remove the turn signal lever, the push button for the four way flashers, and then remove the three screws holding the turn signal switch in place. You can then pull the switch up enough that it's not in the way. You'll see or should see, if it's still there, a small push in thing with two contacts coming off it, that's the switch for the ignition buzzer. It will pop out. Well not exactly pop, you'll need a small screw driver to help it along. You'll then see either a 5/16th or torx screw head bolt, remove and the switch will pull out of the column.

← Older revision		Revision as of 14:35, 24 April 2010
Line 8:		Line 8:


−	Remove the turn signal lever, the push button for the four way flashers then remove the three screws holding the turn signal switch in place. You can then pull the switch up enough that it's not in the way. You'll see or should see if it's still there, a small push in thing with two contacts coming off it, that's the switch for the ignition buzzer. It will pop out. Well not ~~exactely~~ pop, you'll need a small screw driver to help it along. You'll then see either a 5/16th or torx screw head bolt, remove and the switch will pull out of the column.	+	Remove the turn signal lever, the push button for the four way flashers, and then remove the three screws holding the turn signal switch in place. You can then pull the switch up enough that it's not in the way. You'll see or should see, if it's still there, a small push in thing with two contacts coming off it, that's the switch for the ignition buzzer. It will pop out. Well not exactly pop, you'll need a small screw driver to help it along. You'll then see either a 5/16th or torx screw head bolt, remove and the switch will pull out of the column.

@@ Line 1: / Line 1: @@
 By AMC Eagle Nest Member "Pack Rat".
 Note: This How-To starts after the steering wheel has been pulled. Please follow this link for a 'How-To' about removing the wheel.
 [[Re&Re The Wiring Harness in Your Steering Column]]
 Remove the turn signal lever, the push button for the four way flashers then remove the three screws holding the turn signal switch in place. You can then pull the switch up enough that it's not in the way. You'll see or should see if it's still there, a small push in thing with two contacts coming off it, that's the switch for the ignition buzzer. It will pop out. Well not exactely pop, you'll need a small screw driver to help it along. You'll then see either a 5/16th or torx screw head bolt, remove and the switch will pull out of the column.