Front Wheel Bearings - Revision history

IowaEagle at 00:39, 14 January 2006

2006-01-14T00:39:13Z

2006-01-14T00:06:06Z

2006-01-13T23:51:27Z

2006-01-13T23:44:55Z

2006-01-13T23:44:20Z

2006-01-13T23:40:52Z

2006-01-13T01:04:21Z

2006-01-13T01:02:43Z

2006-01-13T00:39:21Z

2006-01-13T00:36:26Z

@@ Line 1: / Line 1: @@
 '''Adapted from the AMC Technical Service Bulletin.'''
@@ Line 298: / Line 296: @@
 .  Install seal installer tool 5080 (Fig. 16) and press inner bearing (U) (Fig. 16) and seal (V) (Fig. 16) onto hub.
@@ Line 307: / Line 317: @@
 [[Image:frontbearingfigure16.jpg]]

← Older revision		Revision as of 00:06, 14 January 2006
Line 256:		Line 256:


−	10. Press bearing carrier (O) (Fig. 14) onto hub (P) (Fig. 13) using bearing installer 5078 and bearing race installer 5077 (Fig. 14).	+	10. Press bearing carrier (O) (Fig. 14) onto hub (P) (Fig. 13) using bearing installer 5078 and bearing race installer 5077 (Fig. 14). NOTE: Be sure appropriate end of bearing race installer tool 5077 is facing downward toward the hub. One end of the bearing race installer is marked "Eagle", and the other end is marked "Jeep".


Line 265:		Line 265:

	[[Image:frontbearingfigure14.jpg]]		[[Image:frontbearingfigure14.jpg]]
		+
		+
		+
		+	11. Pack inner bearing (Q) (Fig. 15) and coat race with All Purpose Lubricant.
		+
		+
		+
		+	12. On Jeep models, coat lip of inner bearing seal (R) (Fig. 15) with grease and place on inner bearing.
		+
		+
		+
		+
		+	'''Figure 15'''
		+
		+
		+
		+	[[Image:frontbearingfigure15.jpg]]
		+
		+
		+
		+	13. Place hub (S) (Fig. 16) and bearing carrier (T) (Fig. 16) on bearing race installer 5077 (Fig. 16) on press.
		+
		+
		+
		+	14. Position inner bearing (U) (Fig. 16) on bearing carrier (T) (Fig. 16).
		+
		+
		+
		+	15. On Jeep models, place inner bearing and seal (V) (Fig. 16) on bearing carrier (U) (Fig. 16).
		+
		+
		+
		+	16. Install seal installer tool 5080 (Fig. 16) and press inner bearing (U) (Fig. 16) and seal (V) (Fig. 16) onto hub.
		+
		+
		+
		+
		+	'''Figure 16'''
		+
		+
		+
		+	[[Image:frontbearingfigure16.jpg]]

← Older revision		Revision as of 23:51, 13 January 2006
Line 237:		Line 237:

	[[Image:frontbearingfigure12.jpg]]		[[Image:frontbearingfigure12.jpg]]
		+
		+
		+
		+	8. Press outer bearing seal (M) into bearing carrier (N) using seal installer 5079 (Fig. 13)
		+
		+
		+
		+	9. Coat lip of bearing with grease
		+
		+
		+
		+	'''Figure 13'''
		+
		+
		+
		+	[[Image:frontbearingfigure13.jpg]]
		+
		+
		+
		+	10. Press bearing carrier (O) (Fig. 14) onto hub (P) (Fig. 13) using bearing installer 5078 and bearing race installer 5077 (Fig. 14).
		+
		+
		+
		+	'''Figure 14'''
		+
		+
		+
		+	[[Image:frontbearingfigure14.jpg]]

← Older revision		Revision as of 23:44, 13 January 2006
Line 229:		Line 229:

	7. Place bearing (K) (Fig. 12) into bearing carrier (L) (Fig. 12)		7. Place bearing (K) (Fig. 12) into bearing carrier (L) (Fig. 12)
−

← Older revision		Revision as of 23:44, 13 January 2006
Line 221:		Line 221:

	[[Image:frontbearingfigure11.jpg]]		[[Image:frontbearingfigure11.jpg]]
		+
		+
		+
		+	6. Pack outer bearing (K) (Fig. 12) and coat race with AMC/Jeep All Purpose Lubricant P/N 8993630 or equivalent.
		+
		+
		+
		+	7. Place bearing (K) (Fig. 12) into bearing carrier (L) (Fig. 12)
		+
		+
		+
		+
		+	'''Figure 12'''
		+
		+
		+
		+	[[Image:frontbearingfigure12.jpg]]

← Older revision		Revision as of 23:40, 13 January 2006
Line 185:		Line 185:

	[[Image:frontbearingfigure10.jpg]]		[[Image:frontbearingfigure10.jpg]]
		+
		+
		+
		+	'''FRONT WHEEL BEARING REASSEMBLY'''
		+
		+
		+
		+	1. Thoroughly clean hub (6) (Fig. 2) and bearing carrier (10) (Fig. 2) with mineral spirits. Dry using compressed air.
		+
		+
		+
		+	2. Assemble press plate 5073 to bearing carrier (1) (Fig. 11).
		+
		+
		+
		+	3. Position bearing race (J) (Fig. 11) into bearing carrier.
		+
		+
		+
		+	4. Position bearing installer tool 5077 on outer bearing race. NOTE: Be sure appropriate end of bearing race installer tool 5077 is facing downward, toward bearing carrier. One end of the bearing installer is marked "Eagle" the outher end is marked "Jeep".
		+
		+
		+
		+	5. Rotate assembled press plate with bearing carrier and repeat steps 3 and 4 for inner race.
		+
		+
		+
		+	CAUTION: Do not overload press when installing bearing races. Bearing races should be flush with machined shoulder of bearing carrier.
		+
		+
		+
		+	'''Figure 11'''
		+
		+
		+
		+	[[Image:frontbearingfigure11.jpg]]

← Older revision		Revision as of 01:04, 13 January 2006
Line 177:		Line 177:

	14. Place on press and press out inner bearing race, rotate and press out outer bearing race. (Fig. 10). CAUTION: Never use anything other than prescribed tools to remover bearing races as damage to the internal machined shoulder of the barrier carrier could result.		14. Place on press and press out inner bearing race, rotate and press out outer bearing race. (Fig. 10). CAUTION: Never use anything other than prescribed tools to remover bearing races as damage to the internal machined shoulder of the barrier carrier could result.
		+
		+
		+
		+	'''Figure 10'''
		+
		+
		+
		+	[[Image:frontbearingfigure10.jpg]]

← Older revision		Revision as of 01:02, 13 January 2006
Line 144:		Line 144:


−	10. On Jeep models, prss the inner bearing seal (G) (Fig. 8) from the hub using the inner race and bearing installer (5078) (Fig. 8).	+	10. On Jeep models, prss the inner bearing seal (G) (Fig. 8) from the hub using the inner race and bearing installer (5078) (Fig. 8). NOTE: Be sure the word "Jeep" on tool 5078 is facing downward toward the hub.


Line 153:		Line 153:

	[[Image:frontbearingfigure8.jpg]]		[[Image:frontbearingfigure8.jpg]]
		+
		+
		+
		+	11. '''On Eagle Models''', position the bearing race remover tool 5075 between the inner and outer bearing races (H) (Fig. 9)
		+
		+
		+
		+	12. On Jeep models, position the bearing race remover tool 5076 between the inner and outer bearing races (H) (Fig. 9)
		+
		+
		+
		+	13. Position press pin 5074 (Fig. 9) on bearing race remover tool.
		+
		+
		+
		+	'''Figure 9'''
		+
		+
		+
		+	[[Image:frontbearingfigure9.jpg]]
		+
		+
		+
		+	14. Place on press and press out inner bearing race, rotate and press out outer bearing race. (Fig. 10). CAUTION: Never use anything other than prescribed tools to remover bearing races as damage to the internal machined shoulder of the barrier carrier could result.

← Older revision		Revision as of 00:39, 13 January 2006
Line 140:		Line 140:


−	9. '''On Eagle Models''', remove the inner bearing (12)~~(Fig.~~ (Fig. 2)	+	9. '''On Eagle Models''', remove the inner bearing (12) (Fig. 2)

← Older revision		Revision as of 00:36, 13 January 2006
Line 95:		Line 95:

	4. Cut and remove the plastic bearing cage (C) (Fig. 5) from the hub inner bearing. Use diagnol pliers or tin snips to cut the bearing cage. Discard the roller bearings after removing the cage.		4. Cut and remove the plastic bearing cage (C) (Fig. 5) from the hub inner bearing. Use diagnol pliers or tin snips to cut the bearing cage. Discard the roller bearings after removing the cage.
		+
		+
		+
		+	'''Figure 5'''



	[[Image:frontbearingfigure5.jpg]]		[[Image:frontbearingfigure5.jpg]]
		+
		+
		+
		+	5. Remove the remaining part of the inner bearing from the hub as follows:
		+
		+	Install remover tool J-22912-01 on the inner bearing (D) (Fig. 6). Then position the remover tool and hub in an arbor press or hydraulic press.
		+
		+
		+
		+	'''Figure 6'''
		+
		+
		+
		+	[[Image:frontbearingfigure6.jpg]]
		+
		+
		+
		+	6. Press the hub (E) out of the inner bearing (F) with press pin 5074 (Fig. 7)
		+
		+
		+
		+	'''Figure 7'''
		+
		+
		+
		+	[[Image:frontbearingfigure7.jpg]]
		+
		+
		+
		+	7. '''On Eagle Models''', remove the O-ring seal (11) (Fig. 2) from the hub. Discard the seal, it is not reusable.
		+
		+
		+
		+	8. On Jeep models, remove the carrier seal (15) (Fig. 2). Discard the seal, it is not reusable.
		+
		+
		+
		+	9. '''On Eagle Models''', remove the inner bearing (12)(Fig. (Fig. 2)
		+
		+
		+
		+	10. On Jeep models, prss the inner bearing seal (G) (Fig. 8) from the hub using the inner race and bearing installer (5078) (Fig. 8).
		+
		+
		+
		+	'''Figure 8'''
		+
		+
		+
		+	[[Image:frontbearingfigure8.jpg]]